Speak to us today

Bristol: 0117 370 7890
Bude: 01288 359 981

Heavy Duty Workshops
Heavy Duty Workshops
Heavy Duty Workshops
Heavy Duty Workshops
Heavy Duty Workshops

Heavy Duty Workshops

  • From £495.00

  • Cladding type: 15mm thick T&G Shiplap including Floor & Roof 
  • Framing type: 1¾” x 1¾”  
  • Internal Height to Eaves: 6ft
  • Internal Height to Apex: 8ft
  • Felt: Standard Mineral Felt 
  • Door: Single 2ft 6” wide with Lock & Key closing.  Doors can be located on long side or gable end 
  • Window Style: Glass, 1 x Opening, others fixed, 24” x 24” panes   

 

The colour samples shown should be used as a rough guide only.

If you require a more accurate match, please contact us for a colour swatch.

Autumn Gold Autumn Gold
Rich Green Rich Green
Red Cedar Red Cedar
Light Brown Light Brown
Golden Brown Golden Brown
Rustic Brown Rustic Brown
Rich Brown Rich Brown

Please read the instructions completely before attempting to assemble the building.   The instructions are intended as a rough guide only and details may vary due to the large variety of sizes and models available.


1. Lay floor panel (A) in desired position.   Remember to leave enough space around the building for the roof overhang and future maintenance. The base must be solid, flat and level.


2. Position the back gable end section (B) on the back edge of the floor.  The lip on the bottom overhangs the floor.   


3. Offer up a side wall panel (C/D) and screw through the gable into the side from the inside using two of the screws provided. On larger buildings the sides may be supplied in two sections and will need joining together using the coach bolts provided.


4. Offer up the other side wall (C/D) and screw in a similar fashion.


5. Offer up the door gable end (E) and screw as before. (Remember to remove the key from the inside of the door and unlock the door first).


6. Place the roof truss if supplied in the middle of the sides and fix with a nail or screw, position the roof purlin (L) so it sits upright on the two gables and rest on the truss.  Place roof panels (F) onto the shed so that the overhang meets at the apex.   


7. Check that the roof is sitting square on the shed.   If it is not then it is likely that your base is not level and the shed will need lifting at one corner with packing to square up the roof before continuing.


8. With the roof square check that all the walls are sitting properly on the base.  Screw the walls to the base using two screws per panel, ensuring that you screw into a floor joist; follow the lines of nails already in the floor to see where the joists are.


9. Screw the two roof sections together through the purlin then secure by nailing through the roof to the framing on the walls using 2” nails.


10. Felt the roof using the small clout nails.   Start with a wide piece of felt and place it on the roof so that it overhangs both ends and the bottom rail.   Secure it with three evenly placed nails along the upper edge and a nail every four to five inches along the bottom rail.   Repeat this for the other wide piece of felt.   Place the ridge felt (narrow piece) along the top of the shed and nail into place from the centre outwards every four to five inches.   Fold the ends of the felt and nail into the end of the framing.   


12. Fix the barge boards (H) to the gable ends of the roof using 2” nails to cover the folded felt.


13. Nail on the diamond finales.


14. Fix the corner strips (I) (long strips) to the corners of the shed with three 2” nails per strip.   


15. Glaze the building from the outside using the beading provided.   Nail with two oval nails on T & G shiplap sheds.   DO NOT push the beading too tight against the glass as this will cause it to crack.   Some models are glazed using oval nails only.


Write a review

    Bad           Good

(1)Select Size

Size Cost

(2)Add Extras

Name Option Cost

Name Option Cost

(3)Enquire

TOTAL PRICE: £495.00

Price Includes VAT and Delivery*

Related Products >

© Copyright Shed Scene 2015 All Rights Reserved.
Telephone: