Speak to us today

Bristol: 0117 370 7890
Bude: 01288 359 981

Double Classic Kennel

Double Classic Kennel

  • From £310.00

  • Cladding type: 12mm thick T & G Shiplap including Roof & Floor
  • Framing type: 1¾” x 1¼”
  • Felt: Standard Mineral Felt
  • Internal Height: 3ft at Apex
  • Features: Arched entrance & Partition wall

The colour samples shown should be used as a rough guide only.

If you require a more accurate match, please contact us for a colour swatch.

Autumn Gold Autumn Gold
Rich Green Rich Green
Red Cedar Red Cedar
Light Brown Light Brown
Golden Brown Golden Brown
Rustic Brown Rustic Brown
Rich Brown Rich Brown

Please read the instructions completely before attempting to assemble the building.   The instructions are intended as a rough guide only and details may vary due to the large variety of sizes and models available.


Parts List

A – 1 x Floor Section

B – 1 x Plain Gable

C – 2 x Plain Side

D – 1 x Door Gable

E – 2 x Roof Sections

F – Felt

G – 1 x Trim Pack

H – 2 x Diamond Finale

I – 1 x Fixings Pack


1. Treat both sides of the floor if the building has been supplied untreated.   Lay the floor panel (A) in its desired position (remember to leave enough space at the back and sides of the building for roof overhang and maintenance).  It is essential the floor is on a solid level base, otherwise the building will not fit together properly.   Place the panels around the floor – it will help you understand how they fit together.


2. Select the plain gable (B on the back edge of the floor (the lip on the bottom of the sides overhangs the floor. Place a plain side (C) on the floor to form a corner.  Check that the sides are sitting flat on the floor and the panels are butted together, screw them together from the inside using the screws provided.


3. Screw the other plain side (C) as before.


4. Screw the door gable (D) to the sides from the inside as before.


5. Screw the panels to the floor ensuring that you screw into a joist; follow the lines of nails in the floor to locate the joists.


6. Place the roof sections (F) on the building so that the overhang on one side of the roof meets at the apex, before fixing check that the roof is square and sitting flat on the sides, if not it is possible the floor is not level and will need packing in one corner.


7. Secure the two roof sections by nailing through the roof into the framing on the sides and gables.


8. Felt the roof using the small clout nails provided. Start by carefully removing the paper from the wide roll of felt; roll the felt out on a flat surface. For the double model cut in half to give two equal strips. Place a strip on the roof so it overhangs each end and approximately 50mm at the side, secure with three evenly spaced nails along the upper edge then fold the felt over the side of the roof and nail every 100 – 150mm along the edge of the roof framing working from the middle outwards.


9. Open the trim pack and select the four fascia boards nail them to the ends of the roof using the nails provided then trim the felt.


10. Nail on the diamond finales.


Before allowing animals to use the Kennel have a good check round to make sure there are no nails or screws protruding especially inside the kennel.


Write a review

    Bad           Good

(1)Select Size

Size Cost

(2)Add Extras

Name Option Cost

Name Option Cost

(3)Enquire

TOTAL PRICE: £310.00

Price Includes VAT and Delivery*

Related Products >

Classic Kennels Kennels & Runs

Classic Kennels

From £130.00

Pent Dog Kennels Kennels & Runs

Pent Dog Kennels

From £565.00

Apex Kennel With Run Kennels & Runs

Apex Kennel With Run

From £735.00

Chicken Coop

Chicken Coop

From £60.00

© Copyright Shed Scene 2015 All Rights Reserved.
Telephone: