Speak to us today

Bristol: 0117 370 7890
Bude: 01288 359 981

Single Cold Frames
Single Cold Frames
Single Cold Frames
Single Cold Frames

Single Cold Frames

  • From £75.00

  • Cladding type: 15mm thick T & G Shiplap
  • Framing type: 1¾” x 1¼
  • Hinged lid with horticultural glass top. Option to change to Acrylic/Perspex. The Lid has 1 timber Prop to keep it open
  • Pre-treated in a choice of 7 colours - see colour options
  • All standard models are 21½” high at rear, sloping forward to 18½” high at front
  • Standard Glass/Acrylic sizes are: 610mm x 457mm (24” x 18”) and 610mm x 610mm (24” x 24”)

Special sizes can be made to suit your own requirements - call for price.

Supplied Flat-packed for Home Assembly.

Should you require delivery please phone for a price.



Model 1 CFS1824
21” W x 27” D
Model 2 CFS2418
27” W x 21” D
Model 3 CFS2424
27” W x 27” D

The colour samples shown should be used as a rough guide only.

If you require a more accurate match, please contact us for a colour swatch.

Autumn Gold Autumn Gold
Rich Green Rich Green
Red Cedar Red Cedar
Light Brown Light Brown
Golden Brown Golden Brown
Rustic Brown Rustic Brown
Rich Brown Rich Brown

Please read the instructions completely before attempting to assemble the cold frame.   The instructions are intended as a rough guide only and details may vary due to the large variety of sizes and models available.

Tools required: Drill, Pin Hammer, 3mm Pilot Drill Bit, Phillips Screwdriver, Sharp Knife, Gloves, Saw

1. Using a flat level surface, place together 1 x end panel and the taller, rear panel.   Make sure the rear panel sits inside of the end panel.  Roughly line them up so that the vertical framing of both panels are butted-up to each other.  Drill a small pilot hole – top, middle and bottom of the rear panel.   Note – the pilot holes should be drilled completed through the vertical frame of the rear panel.

2. Once pilot holes have been drilled, ensure that the outside face of the rear panel is flush with the rear, higher edge of the end panel. Once flush, insert and tighten all 3 screws. Repeat 1, 2 & 3 for lower front panel & remaining end.  

3. Lay the lid panel on a flat surface with the rebate facing upwards.   Place either your glass or acrylic into the rebate ensuring all 4 edges are supported . Take 4 lengths of beading, 2 short and 2 long, for rectangular coldframes.  4 equal lengths for square coldframes.   Beading may need to be trimmed if too tight a fit. Press each length of bearding against both the frame and the glass/acrylic, for a firm hold, and nail the beading to the frame using pins supplied.  Use at least 4 pins per bead.

4. Once glazed, carefully place the lid panel onto the assembled coldframe body.   Make sure that the hinges are positioned on the high rear panel and flat against the cladding of this panel.  Square up the lid so that it sits equally side to side (the front edge will overhang the body slightly). Using the shorter screws, fix and tighten hinges to the body of the coldframe.

5. Fitting the Handle.   Position and mark handle position, approximately centre of lid edge.   Fix and tighten screws.

6. Acrylic only.   Once completed assembled, take a sharp knife and lightly score the film of the acrylic around the beading on both sides.   This will allow you to remove the protective film.

Write a review

    Bad           Good

(1)Select Size

Size Cost

(2)Add Extras

Name Option Cost

Name Option Cost



Price Includes VAT

Related Products >

Potting Sheds

Potting Sheds

From £1,435.00

Solar Sheds

Solar Sheds

From £845.00

Double Cold Frames

Double Cold Frames

From £95.00



From £10.00

Slotted Raised Beds

Slotted Raised Beds

From £52.00

© Copyright Shed Scene 2015 All Rights Reserved.